I have 2 ultrasone sensors connected via a raspberry pi to IoT services (see result below). Everything works fine however there is a 5 second delay (as you can also see in the table; G_created is timestamp from HCP, C_storedat is the timestamp from the Pi). The IoT services seems to handle the incoming values as a batch job each 5 seconds. Do you have any idea how to make this delay smaller so I can have a (near) real time dashboard?
Thanks again!
Frank
G_DEVICE | G_CREATED | C_UNIT | C_STOREDAT | C_VALUE |
|
78dcb2bc-d05f-47cc-a82e-8a4b0e3b15d1 | 2015-12-28 11:11:09.891 | Centimeter | 20151228111104816 | 16.29 |
|
78dcb2bc-d05f-47cc-a82e-8a4b0e3b15d1 | 2015-12-28 11:11:04.891 | Centimeter | 20151228111100166 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:11:04.891 | Centimeter | 20151228111101744 | 16.29 |
|
78dcb2bc-d05f-47cc-a82e-8a4b0e3b15d1 | 2015-12-28 11:11:04.891 | Centimeter | 20151228111102492 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:11:04.891 | Centimeter | 20151228111104069 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:10:59.89 | Centimeter | 20151228111054769 | 16.29 |
|
78dcb2bc-d05f-47cc-a82e-8a4b0e3b15d1 | 2015-12-28 11:10:59.89 | Centimeter | 20151228111055517 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:10:59.89 | Centimeter | 20151228111057092 | 16.29 |
|
78dcb2bc-d05f-47cc-a82e-8a4b0e3b15d1 | 2015-12-28 11:10:59.89 | Centimeter | 20151228111057841 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:10:59.89 | Centimeter | 20151228111059419 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:10:54.89 | Centimeter | 20151228111050118 | 16.29 |
|
78dcb2bc-d05f-47cc-a82e-8a4b0e3b15d1 | 2015-12-28 11:10:54.89 | Centimeter | 20151228111050866 | 16.29 |
|
b824aaf8-315f-4c2c-93b9-ff0e3b8379a1 | 2015-12-28 11:10:54.89 | Centimeter | 20151228111052444 | 16.29 | |